The tapered barrel on these bushings is split on both sides, permitting them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They’re for work with with split-tapered sprockets and pulleys of the same bushing style. As you tighten the included screws, the bushing grips the shaft and pulls it in to the sprocket or pulley.
This Split Taper Bushing was created exclusively for use with cast iron bushed bore pulleys and can be purchased on the same page as the pulley you will need. For apply with 5/8” shaft sizes. Includes set screws. Added Features: Manufactured from Steel For make use of with cast iron bushed bore pulley
Our stock metal Split Taper bushings feature wrench torque potential from 95 to 3,000 pounds and bore sizes from 3/8″ to 6-3/16″.
The split tapered bushing is a flanged bushing. Split tapered bushings are used on sheaves, pulleys, sprockets and equipment belt pulleys. The split tapered bushing alleviates the necessity to have an element bored to size, ideally lowering readily available requirements and enabling improvements in shaft size if necessary. The barrel of the split tapered bushing is split in two areas and is normally keyed to the shaft. The barrel OD is also keyed to the travel component as well. The benefit of the split tapered bushing could it be will hold, even if the fasteners become loose. Split tapered bushings will be interchangeable between manufacturers.

Taper bushing are widely used together with sprockets, v-belt pulleys, timing pulleys, coupling and other mechanical parts with taper bore connections.
Taper bushing series are made of high quality engineered supplies with great tolerance. The feature is easy to make use of and needs no added alteration. These bushings can go well with almost all types of assemblies and sizes. They will be the best choice in style for mechanical connections.
To complete designations add bore size. For instance: PD1215X16MM designates a 1215 taper bushing with a 16mm bore.
No costly re-boring: complete range of both metric and imperial readily available.
Standard range fits up to 125mm/5″ shafts & Hub diameter required is determined by the application.
Complete brief reach range obtainable, for compact compact assemblies & Clean, Compact Design.
Ease of installation and removal.
This Split Taper Bushing is designed exclusively for use with cast iron bushed bore pulleys and may be purchased on a single page as the pulley you need.
For use with 1 3/16” shaft sizes.
Includes 2 set screws.

Additional Features:
Made of Steel
For use with cast iron bushed bore pulley
This U1 Bushing with 5-1/2″ bore is a high-quality precision product that is built for sturdiness and strength. U1 bushings are being used in an extensively wide variety of applications, which include; sprockets, shaves, pulleys, gears, and much more, we also offer most of these items. What units this bushing apart may be the high-quality steel building along with exact manufacturing and top quality control; this means that you always get a premium quality steady product. What really sets us apart from the other fellas is our experienced expert workers and our company-wide aim of customer satisfaction.
1. Be certain the tapered cone areas of the bushing and the within of the driven product happen to be clean and free of anti-seize lubricants.
2. Place the bushing in sprocket or various other component type that accepts the bushing.
3. Place cap screws loosely in pull-up holes. The bushing continues to be loose to assure sliding in shape on shaft.
4. With crucial on shaft, slide the sprocket or other portion type to the required posture on the shaft. Be sure to leave the heads of the cap screws available.
5. Align the sprocket or portion type, tighten the screws additionally and progressively until they happen to be pulled up tight. Do not make use of extensions on the wrench handles , nor permit the sprocket or component to end up being drawn i contact with flange of bushing. At this point there should be a gap between your bushing flange and sprocket, make certain this gap will not close.
Dual split barrel ensures concentricity
Grips the shaft with great clamp fit
High torque carrying capacity
Permits blind assembly
Load not carried or limited by mounting screws
External key on most sizes for great drive and increased torque carrying capabilities
Double-split barrel for great clamping
Solid flange to keep up concentric bores
Available in “, metric, and spline bores. Bore range between 3/8″ to 10”
Solid Flange & Dual Split Barrel – Assures better concentricity to the shaft.
Key to Key Drive – With keys in both the shaft and product to provide the strongest possible travel.
3/4″ per Foot Taper on Barrel – Self locking taper supplies the highest amount of mechanical locking item to product.
The tapered barrel on these bushings is split on both sides, permitting them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They’re for apply with split-tapered sprockets and pulleys of the same bushing design. As you tighten the included screws, the bushing grips the shaft and pulls it in to the sprocket or pulley.
This Split Taper Bushing is designed exclusively for use with cast iron bushed bore pulleys and may be purchased on a single page as the pulley you need. For make use of with 5/8” shaft sizes. Includes set screws. Extra Features: Manufactured from Steel For make use of with cast iron bushed bore pulley
Our stock metal Split Taper bushings feature wrench torque potential from 95 to 3,000 pounds and bore sizes from 3/8″ to 6-3/16″.
The split tapered bushing is a flanged bushing. Split tapered bushings are used on sheaves, pulleys, sprockets and equipment belt pulleys. The split tapered bushing alleviates the need to have an element bored to size, preferably lowering on hand requirements and enabling changes in shaft size if necessary. The barrel of the split tapered bushing is split in two locations and is certainly keyed to the shaft. The barrel OD can be keyed to the drive component as well. The advantage of the split tapered bushing could it be will hold, whether or not the fasteners turn into loose. Split tapered bushings are interchangeable between manufacturers.